Classic gel for extensions with glitter Shimmer Gel – a polymeric light-curing material that, due to its strength, allows you to significantly lengthen the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.
Features:
- It is acid-free.
- It has cushioning and does not crack during impacts.
- It has a medium-thick consistency.
- It has medium pigmentation, covers the free edge.
- Suitable for the "build-up without filing" technique.
- Suitable for building up "on top forms".
- Does not cause burning in the lamp.
- It becomes thicker in the cold, and thinner in the heat.
- Thixotropic - becomes thinner if you move the brush while working.
- It can be heated further to make the gel thinner.
- Harder than 1mm thick. If the thickness is less than 1mm, it may sag a little, but it does not affect the wearability.
- It does not shrink and holds the arch well.
- Definitely needs a backing of Rubber Base .
- The wavelength for polymerization is 365-405 nm.
- UV/Led lamp power 36-48W.
- The permissible coating thickness is 0.5 mm at the end/1 mm at the apex.
- Full polymerization 120 seconds.
Application method:
STRENGTHENING
- Withdrawal.
- We do not file the nail shape or leave it 2 mm long, which we will remove after leveling.
- Use a 220-grit file to file the nail without applying strong pressure from above, lifting the scales of the nail plate, or use a 100-grit buff.
- Let's do a manicure.
- If we work with removers, we wash our hands with soap after working with them.
- Degrease the nail with Nail Prep . We do two approaches. We use 4 wipes for this (1 wipe for 5 fingers). The first approach: wipe the surface of the nail. The second approach: take an orange stick, put a wipe on it and wipe everything in the cuticle area and in the sinuses.
- We use a primer if desired, but if the base for the substrate has sufficient acidity, then it is not needed.
- Substrate from Rubber Base LUNAmoon It is best to apply with a flat gel brush. The movements should be rubbing. We draw all the sinuses of the nail and dry in the lamp for 60 seconds.
- We erase the stickiness.
- Level with gel, leaving 0.5–1 mm from the cuticle. Dry in the lamp for 60 seconds.
- File the shape after it has been smoothed out. This is necessary so that a thickness forms on the edge of the nail that will hold the free edge.
- If the nail was thin, it may curl, so be sure to cut 1 mm of the natural nail from the inside. In this case, there will be no peeling of the material. If the material is hard and the nail is very soft, the nail itself will begin to separate from the hard material from the free edge.
- After filing, we erase the stickiness and cover with gel polish.
602215d2f3c4a8469e4fb284b">Cover with top coat. Dry for 120 seconds. After drying, do not wipe with anything, as the shine may be lost.
CLASSIC EXTENSION
- Withdrawal
- We shorten the length of the nail to 1 mm and make a round shape.
- Use a 220-grit file to file the nail without applying strong pressure from above, lifting the scales of the nail plate, or use a 100-grit buff.
- Let's do a manicure.
- If we work with removers, we wash our hands with soap after working with them.
- Degrease the nail with Nail Prep . We do two approaches. We use 4 wipes for this (1 wipe for 5 fingers). The first approach: wipe the surface of the nail. The second approach: take an orange stick, put a wipe on it and wipe everything in the cuticle area and in the sinuses.
- We use primer .
- Substrate from Rubber Base LUNAmoon It is best to apply with a flat gel brush. The movements should be rubbing. We draw all the sinuses of the nail and dry in the lamp for 60 seconds.
- We erase the stickiness.
- We set the form for building the free edge of the nail.
- Apply the clear gel to the shape of the artificial nail. Dry for 30 seconds.
- File the free edge and give the nail the desired shape.
- Wipe away the stickiness and excess dust.
- Let's walk again. Rubber Base LUNAmoon on the areas where the saw was used. Dry for 30 seconds.
- Level it with gel, place it in the lamp and clamp it for 10–15 seconds. If the gel is very sticky or contains glitter, clamp it for 20 seconds.
- Dry in the lamp for 120 seconds.
- We erase the stickiness before covering with gel polish.
- Cover with top coat. Dry for 120 seconds. After drying, do not wipe with anything, as the shine may be lost.
Ingredients INCI: Acrylates Copolymer, Hema, Mica, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica Dimethyl Silylate.
May contain: CI 77891, CI 77266, CI 18965, CI 15510, CI 73360, CI 73900, CI 51319, CI 74160, CI 74260, CI 73915, CI 77007, CI 77492, CI 45405, CI 59040
Product expiration date: 24 months. Store opened for no more than 18 months.
TPO FREE
(Product photos on the website may differ from the actual product)
Luna Shimmer Gel №07, 30 ml
